C-More       small      medium    large

CPWSA Logo Scopecoat - The Devtron Scopecoat™ is constructed of high quality neoprene and laminated with nylon. Simple design safeguards your C-More or scope from dings and scratches, dust, dirt, and moisture. The shock and moisture absorbing Neoprene helps draw moisture and condensation away from your sight and helps protect it from the elements.  The C-More model also fits Trijicon Reflex scopes.  

The scope models are now offered in the XP-6 "flak jacket" model.  This is the thicker 6mm weight which is three times thicker than regular scopecoats and offers the ultimate in scope protection.  Available for small, medium, and large rifle scopes.  Measure your scope length and objective to determine correct size.  Small is 6.5" long for 20/30mm objectives like the Valdada IOR; medium is 9" long for 30mm objectives or CQT type scopes; large is 12.5" long for 42mm objective scopes.  Scopecoats stretch approximately 10% and the correct fit is either relaxed or snug.

AR-15 Receiver Rugs - this ingenious little device can save your match or your life.  Rubber molded 3-dimensional gasket that blocks blown primers and other debris from wedging under the trigger action.  Designed for easy installation into the bottom of the lower receiver.  A must for competition shooters, 3-gunners, military and law enforcement personnel.  Available in two models.  The black rug is $5 and non-molded for adjustable triggers, and the red rug is $9 and molded for Mil-Spec non-adjustable triggers.

AR-15 Anti-Walk Pins - These DPMS pins replace the original hammer trigger pins. They extend past the receiver on each side and are retained by special retaining rings for a more positive lock.  2 pins and clips per set.

TAC-GRIP™ - created in the quest of finding a better and affordable product to enhance the grip on weapons and tools.  TAC-GRIP™  is pre-cut grip tape.  Yes, I know, you're thinking "one more pre-cut-tape on the market".  Well, not really.  TAC-GRIP™  comes in standard black and sand, but also blue and red as well.  It can be taken off and re-applied up to four times yet leaves no sticky residue on the weapon.  Increases weapon control and retention under extreme tactical conditions.  Designed especially for military and law enforcement use.  Available for M4/M16/AR15, Glock 17/22/34/35, Glock 19/23, and Springfield XD models.  Packaged 3 per pack.

Arredondo AR-15 Magwell - works just like the magwell on a handgun.  Guides the magazine into the opening even when it's not exactly aligned.  The well in use by the 82nd Airborne Division in Iraq proves this product is valued outside the competitive arena.   Available in black and desert sand colors.

Arredondo ACOG J-Point Mount - reduce to offset created by most secondary optic mounts.  Provides amazingly quick target acquisition.  Includes 5-40 and 8-32 mounting screws.

Arredondo Doctor Mount for Benelli - includes mounting screws and adapter plate for DOCTER sight.  Attaches to sight rib to assure constant zero.

Arredondo AR-10 Magazine Basepad - this pad fits AR10, M1A, and M-14 magazines.  Like the AR-15 basepad, can be used as a mag pull, a prone position mono-pod base, or used on top of the mag to protect ammunition and prevent dirt from entering magazine. Available in black only.

AR-15 Magazine Pads - can be used as a mag pull, a prone position mono-pod base, or used on top of the mag to protect ammunition and prevent dirt from entering magazine.  Fits all metal and HK type magazines.    Available in black or desert sand colors.

AR-15 Mag Yoke - this yoke is designed specifically to work with the Arredondo AR magwell.  Allows you to keep that extra magazine on the weapons as opposed to on the body.  Comes in set of 2 and available in black or desert sand colors.

AR-15 Oversize Magazine Release - simply replace your existing release with this enlarged button.  No gunsmithing required.  Available in black and desert sand colors.

AR Safety Flag - required at many 3 Gun events to easily and visually ensure weapons is unloaded.  Bolt must be in open position to insert.  Spring loaded auto eject.  Dust cover can be closed with flag inserted.

Nordic Components - extended magazine tubes for Benelli and Remington shotguns.  These are the most well machined tubes available in my opinion.  Unique swirl barrel nut adds a distinct touch while providing a sure grip should field takedown be necessary with gloved hands.  Available in both tactical/limited and open division length models.  Available in 12 gauge for Remington 870/11-87/1100, Benelli M1/M2/SBE/SBE2, and Benelli Nova shotguns.  Tube length options are +4 and +5 for limited/tactical and +7, +8 and +9 for open division guns.  Nordic Component shell capacity is referenced as the shell increase above and beyond the stock capacity.  For example, if your Benelli Nova holds 4 shells in the factory tube, and you install a +4 Nordic tube on your gun, you'll end up with a 9 round capacity; 8 in the tube and 1 in the chamber.  Be sure to get your Nordic barrel clamp below.   Includes tube, barrel nut, and spring.

Nordic Barrel Clamp - Nicely machined barrel clamp to secure your Nordic extended tube.  Now in stock.

Nordic Components Charge Handles -  this is the extended bolt release that exactly matches your Nordic extended tube.  Same unique swirl design pattern that provides a sure, non-slip surface when needed to charge your gun quickly for those empty chamber starts.  Fits Benelli M1/M2/Beretta Extrema/Extrema 2/Franchi 620 & 720.

Oversize Benelli Bolt Release Button - installs over factory release and requires drilling and tapping of existing button.  11/16" diameter.  Free shipping.

Low Drag Magazine follower - aluminum follower, teflon coated and anodized.  Eliminates shell binding that can occur when feeding from high capacity tubes.

Titan AR-15 .223 Compensator - designed by USPSA Grandmaster Erik Lund along with SJC.  Gas vectoring technology maximizes recoil reduction and minimizes torque and shot to shot recovery time.  Unique design traps expanding gas in the baffles and increases dwell time for maximum efficiency.   I have this comp on my open division rifle, even though the comp is limited and tactical division legal.  That should tell you something about it's effectiveness. Optimized to work with any barrel length.  Threaded for 1/2 x 28 threads.  Erik introduced and used this comp in his 3rd place overall Tactical division finish at the 2006 Area 6 3-Gun Championship.  Available in blue or stainless steel versions.  The blued model is $90 and the stainless steel model is $120. 

Here's a link to a video where you can see just how flat the Titan really is:  2007 GA State 3 Gun.mpg

.308 Titan comp - now in stock.  Get Titan performance for your .308.  Tapped for standard 5/8 x 24 .30 caliber threads.  Blued finish only.  Limited and tactical division legal.  Price is $100.

2006 Multi-Gun Nationals Video - The 2006 USPSA Multi-Gun Nationals brought to the Albany Rifle and Pistol range the best shooters from across the country, to compete for the top honor in the sport of Multi-Gun.  Double-Alpha Academy was there to bring you the best possible coverage of this exciting event! 
 
In this production we follow the shooters of Squad One, which included the top competitors in both the Open and Tactical Divisions.  Watch Open division champions Michael Voight, Jerry Miculek, and Matt Burkett battle it out with pistol, shotgun and rifle.  See the skill and speed of Tactical division superstars, Taran Butler, Bennie Coolley and Barry Dueck. 
 
80 minutes of action packed Multi-Gun competition, filmed and edited by professional shooter Saul Kirsch, who gives his insight and tactical analysis of the stages shot.  Includes hat-cam action shot by Chris Tilley, as well as interviews, scores and stage results. 

Here's a couple of sample clips from the video:

Multi-Gun Intro

Bennie Cooley at Multigun

Bennie Cooley's 11 - this DVD video is a must for anyone who desires to master the AR-15 rifle.  Bennie shares the methods and techniques he used to win 11 Major championships.  Over 100 minutes of instruction including equipment and ammo, maintenance, barrel break-in, shooting drills, supported and un-supported shooting positions, shooting on the move, zeroing in, and much more.

Lula magazine loader - fits all M16/AR-15 type metal and polymer magazines except H & K 5.56mm steel mags.  This loader is the ticket.  Unloads mags as fast as it loads them.  Eliminates wear and tear on magazine feed lips and more importantly, your fingers.   Prolongs magazine life.  Lightweight and fits easily in your pocket.  Currently in use with the Israeli and other military and special forces, and LE agencies.

Also available for .308 FN FAL metric and inch type, and L4A1/L1A1 magazines.

O-Ring Barrel Seal for Remington 1100 and 11- 87 shotguns.  Made of 75 durometer Viton and just a tad softer than the factory barrel seal for a superior seal between the barrel and the magazine tube.  Viton has superior chemical and heat resistance. Do not confuse Viton with Buna-N, which is a general purpose material with much poorer characteristics. When you buy an o-ring at the local hardware store, you're getting Buna-N. Buna-N is only rated to 270F and is not suitable for use in your shotgun. It will cook to death in short order. Viton is rated to 400F and will hold up to the heat thrown at it by the practical shooter or law-enforcement user.  Any o-ring that's seen more than 500 to 1000 rounds should be considered suspect and discarded.

ISMI AR-15 30 and 40 Round Mag Spring - keep that 30, 40 or 45 round mag functioning properly with these ISMI mag springs.