Extreme Engineering action components, miscellaneous frame, slide, and custom parts.

Tool-less Guide Rod - they're finally back!  A great upgrade for your pistol  Main rod is machined from one solid piece.  No threads to cause stress points where this part can break. The tool-less design is brilliant.  The lock lever is slightly below flush and designed so it stays put until you wish to lock it in place to disassemble your pistol, with no tools!  That's right.  No tools, pins, or clips needed.  It locks the spring, guiderod, and spring plug in one neat assembly so you can easily remove it or replace it.  There are two rods available.  One Fits 1911, Kimber, STI and SV with 5 inch bull barrels and the other fits standard bushing barrel type guns.  Pistol must be able to remove spring plug from the rear of the slide. Includes Tool-less Guide Rod with Full Shoulder Reverse or Standard Bushing Barrel Type Spring Plug.

Aftec Extractor - without a doubt the most widely used extractor in competition today, and for good reason.  Ultra reliable with replaceable coil springs for increased service life.  Available for all popular calibers.

Aftec Replacement Springs - never hurts to keep a few extras on hand in case of wear, breakage, or loss.  Sold in packs of 4.

Sidewinder Slide Rackers - The best slide racker available in my opinion.  Is designed just right to accomplish the necessary purpose but not get in the way.  This is the unfinished model with no set screw.  The unfinished part gives you the option of either a set screw, or ball and detent installation.  Fits .360 x 60 dovetail.   

1911 Slide Stop - .200" diameter pin improves barrel-to-slide lockup for improved accuracy.  Checkered tab provides positive thumb engagement.  Blued steel.

STI Slide Stop - STI factory slide stop for 1911/2011 guns.  Blued steel.

McCormick Grip Safety - forces gun higher up into your hand for improved recoil control.  Raised palm pad ensures deactivation.  Blued steel and requires alteration of frame.

Swenson Thumb Shield Safety - Ambi thumb safety with integral thumb shield to prevent slide interference.  Allows for "thumb ride" grip which allows the highest hand placement available on the weapon.  Large, oversize thumb contact area is curved to match the natural shape of the thumb.  Provides more leverage for better recoil control.  Stainless steel.  Fits 1911/2011 autos and requires fitting for proper installation.

STI Guide Rod - one piece, solid 4140 5.1" steel guide rod improves function and reliability of competition and carry guns.  Fits 1911/2011 style guns.  Drilled for takedown pin.

EGW Ejector - hardened to Rc 40-42, this competition grade ejector is left long at both ends for precise fitting.  Fits 1911/2011 style 9mm/38 guns.  Steel, in-the-white.

STI 2011 pin set - complete pin set for 2011 style pistols.  Never hurts to keep spares on hand.

STI Firing Pin Stop - stock STI firing pin stop for 1911/2011 style guns.  Fits 9/38/40 calibers.

M2i Custom Tactical Firing Pin - Matt McLearn design made from 420 stainless steel with a RC hardness of 50.  This pin is .030 longer than standard with a shank designed to prevent primer flow.  Fits 1911, Kimber, Springfield, STI, SV, and Para in 9mm, 38 Super, and 40 S&W calibers.  Series 80 compatible.  Oversize and requires fitting.

STI Titanium Hammer Strut - combine this strut with other lightweight components for increased performance and improved accuracy.  Improved geometry helps eliminate interference with most grip safeties.  EDM machined from titanium alloy.

Aluminum Shock Buffs - eliminates the bounce that traditional shock buffs generate.  Acts like a dead blow hammer to reduce recoil.  Can also be used to shorten the stroke on full length guns.  CNC machined from aircraft grade aluminum, not molded or stamped.  .100 thick.

EGW Shock Buffs - traditional rubber polymer shock buff to dampen recoil and protect your frame.  Sold in packs of 6.